Oil Plus 2C is a hardwax oil wood finish that colours and protects in only 1 single layer! Using advanced molecular bonding, it protects wood from water, heat and daily wear & tear. It is the best oil for wood furniture, hardwood flooring, tables, and just about anything made out of wood!
A short ‘dry’ maintenance period: after 5 days, the surface can be cleaned with water and Rubio Monocoat Soap.
Specifications
Spread Rate
300-500 ft²/L (30-50 m²L)
Spread Rate by Packaging
6 ml (Part A only) = sample 20 ml (Part A only) = sample 100 ml (Part A only) = 30-50 ft² (3-5 m²) 130 ml = 39-65 ft² (3.9-6 m²) 350 ml = 105-175 ft² (10-17 m²) 1.3 liter = 390-650 ft² (35-60 m²)
Cure Time
Within 5 days
VOC Content
0%
Colour Options
55
Dilutable
No
Shelf Life
36 months
Combustion warning
Cloths, saturated with oil, may spontaneously combust. After usage, they need to be soaked in water before disposal.
Instructions
An overview of instructions. Please consult the TDS for complete product information.
Application
Furniture, stairs & countertops
Sand the surface scratch-free, up to 120 or 150 grit.
Vacuum thoroughly, eliminate remains of dust with Rubio Monocoat Cleaner and wait until the surface is completely dry (check the technical datasheet of Rubio Monocoat Cleaner before use).
Stir the A component until a homogenous mixture is obtained. Carefully mix the two components (1 to 2 minutes) with a ratio of appr. 3 units A to 1 unit B.
Spread out a small quantity of Rubio Monocoat Oil Plus 2C using the Rubio Monocoat Applicator Set. *Spatula method: evenly spread Rubio Monocoat Oil Plus 2C with a stainless spatula in zones which can be finished within 15 minutes (including step 5). *For ceilings and walls, apply Rubio Monocoat Oil Plus 2C to the surface using a brush and spread using the Rubio Monocoat Applicator Set.
Allow to react for 3-5 minutes. Wipe away all excess oil with a clean terry cloth. Within 10-15 minutes from initial application, perform a final pass using a clean terry cloth, ensuring all excess is thoroughly removed. The surface should be dry to touch upon completion.
Floors
Sand the surface scratch-free according to NWFA guidelines, up to 120 grit.
Vacuum thoroughly then clean remaining dust using Rubio Monocoat Cleaner and wait until the surface is completely dry (check the technical datasheet of Rubio Monocoat Cleaner before use).
Stir the A component until a homogenous mixture is obtained. Carefully mix the two components (1 to 2 minutes) with a ratio of appr. 3 units A to 1 unit B.
Apply the oil to the perimeter of the room. Remove excess oil using a clean terry cloth within 10-15 minutes.
Working in 50-100 ft² (5-10 m²) sections (or areas you can complete within 10-15 minutes), wipe the oil onto the wood and use a white or red buffer pad to equally spread the oil. Continue spreading the oil until the buffer pad no longer forms oil/ colour rings. Complete steps 6 & 7 before starting a new section. *Spatula method: evenly spread Rubio Monocoat Oil Plus 2C with a stainless spatula.
Allowing a reaction time of at least 3-5 minutes, use a clean white buffer pad to remove all excess oil off the 50-100 ft.² (510 m²) section.
Thoroughly remove all excess oil within 10-15 minutes of initial application by placing a clean terry cloth under a clean white buffer pad. If needed, remove all excess oil from v-grooves/bevels and holes by hand.
Continue working in zones you can complete within 10-15 minutes. The surface should be dry to touch upon completion.
Maintenance
Maintenance should be performed using Rubio Monocoat Renew (check the technical datasheet of Rubio Monocoat Cleaner before use).
Repair and renovation
If the Rubio Monocoat Oil Plus 2C treated surface shows much wear and tear, or needs a colour repair, maintain with Rubio Monocoat Oil Plus 2C in the original colour.
Use Rubio Monocoat Surface Care Spray to clean the wooden surface. If there are still some stains, try repeating the cleaning process or using Rubio Monocoat Tannin Remover to remove the stain (check the technical datasheet of Rubio Monocoat Tannin Remover before use).
Abrade the wood surface using a buffer with a maroon pad.
Vacuum thoroughly then clean remaining dust using Rubio Monocoat Cleaner and wait until the surface is completely dry (check the technical datasheet of Rubio Monocoat Cleaner before use).
Stir the A component until a homogenous mixture is obtained. Carefully mix the two components (1 to 2 minutes) with a ratio of appr. 3 units A to 1 unit B.
Apply the oil to the perimeter of the room. Remove excess oil using a clean terry cloth within 10-15 minutes. *Spatula method: evenly spread Rubio Monocoat Oil Plus 2C with a stainless spatula.
Working in 50-100 ft² (5-10 m²) sections (or areas you can complete within 10-15 minutes), wipe the oil onto the wood and use a white or red buffer pad to equally spread the oil. Continue spreading the oil until the buffer pad no longer forms oil/ colour rings. Complete steps 6 & 7 before starting a new section.
Allowing a reaction time of at least 3-5 minutes, use a clean white buffer pad to remove all excess oil off the 50-100 ft.² (510 m²) section.
Thoroughly remove all excess oil within 10-15 minutes of initial application by placing a clean terry cloth under a clean white buffer pad. If needed, remove all excess oil from v-grooves/bevels and holes by hand.
Continue working in zones you can complete within 10-15 minutes. The surface should be dry to touch upon completion. Note: High temperatures may decrease working time and low temperatures may increase the amount of time needed for a molecular bond to occur.
ICE EPOXY DEEP POUR CASTING CRYSTAL CLEAR ICE-CAST is a two component epoxy casting system. It is UV resistant and has anti-yellowing properties, strong adhesion, good fluidity, natural defoaming. It...
ICE EPOXY METALLIC POWDER COLORATION Our high-quality metallic powder adds a mesmerizing sparkle to any epoxy resin project. Perfect for use in jewelry making, resin art, and other crafts, our...
ICE EPOXY THIN CRYSTAL CLEAR RESIN 2 x 1 GAL KIT // ICE THIN is a two component epoxy casting system. UV resistant, it has anti-yellowing properties, strong adhesion, good fluidity, fast curing. It...
ICE EPOXY DEEP POUR CASTING CRYSTAL CLEAR ICE-CAST is a two component epoxy casting system. It is UV resistant and has anti-yellowing properties, strong adhesion, good fluidity, natural defoaming. It...
ICE EPOXY THIN CRYSTAL CLEAR RESIN 2 x 64 oz KIT // ICE THIN is a two component epoxy casting system. UV resistant, it has anti-yellowing properties, strong adhesion, good fluidity, fast curing. It...
ICE-PIGMENT Coloring pigment paste Ice Epoxy's Coloring Pigment Paste features advanced coloring technology with highly concentrated epoxy resin pigments. This is because these rich pasty pigments set themselves into...
ICE EPOXY THIN CRYSTAL CLEAR RESIN 2 x 1L KIT // ICE THIN is a two component epoxy casting system. UV resistant, it has anti-yellowing properties, strong adhesion, good fluidity, fast curing. It is used...
ICE EPOXY RAPID SET EPOXY CRYSTAL CLEAR 16 oz KIT - Fast drying epoxy for sealing wood. Penetrates deeply into the fibers of any type of wood. Ideal for sealing...
Shipping and delivery
All products on our web site are shipped by a carrier chosen by Ice Epoxy.
It is customer’s responsibility to ensure that the delivery can be received in accordance with the carrier’s schedule.
Any additional delivery fees will be the responsibility of the customer. The carrier may charge extra costs in the event of delivery issues.
Ice Epoxy ships products by regular ground delivery service, generally in 1 to 7 business days, but this interval may be longer as delivery times are estimates and may not be guaranteed.
The customer authorizes the shipper and delivery company to leave all packages without proof of signature. Ice Epoxy will not be responsible for lost, missing or stolen items.
Items that are back-ordered are shipped immediately upon arrival in the warehouse.
Refunds and returns
There are no refunds or returns on products, materials or supplies.
Defective products, materials or supplies will be replaced by Ice Epoxy. Customers must notify Ice Epoxy of any damaged or defective products, materials or supplies within 24 hours of reception and supply proof upon request. It is the customer’s responsibility to inspect products, materials or supplies upon delivery.
No refund or return may be made after products, materials or supplies have been used and/or mixed and/or installed.
All repackaging costs, return shipping and/or delivery costs will be the customer’s responsibility. All products, materials and supplies must be returned in saleable condition.